[Berlin-wireless] Arcadyan / Astoria ARV752DPW22 EasyBox 803A
Matthias Klose
matthias at klose.berlin
Mo Feb 11 20:36:01 CET 2019
Hi Stefan,
der Hammer. Danke. Bist ein Schatz. Das bootet!! Einzig hat er noch kein WLAN. Würde ihn auch mit dem 2800er USB-Dongle betreiben. Er hat immerhin drei USB-Host-Ports, in drei unterschiedliche Richtungen zeigend :)
Sehe ich das richtig, dass
[ 0.286315] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
vielleicht die WLAN-Hardware sein könnte? Ansonsten ist er Router im Ist-Zustand auch schon schön als Offloader mit LAN-Mesh-Antennen dran brauchbar. 5/5 User Experience, would flash again.
Gruß Matthias
Hier der Serial-Bootlog:
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X
U-Boot 2013.10-openwrt4 (May 28 2014 - 21:46:54) ARV752DPW22
Board: Arcadyan ARV752DPW22
SoC: Lantiq Danube-S v1.5
CPU: 333.333 MHz
IO: 166.667 MHz
BUS: 83.333 MHz
BOOT: NOR
DRAM: 64 MiB
Flash: 8 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: ltq-eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0040000 ...
Image Name: MIPS LEDE Linux-4.4.167
Created: 2019-01-15 14:51:19 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1438411 Bytes = 1.4 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.4.167 (user at Ubuntu-Toshiba) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2993+1010-b9a408c2b4) ) #0 Tue Jan 15 14:51:19 2019
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019641 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ARV752DPW22 - Arcor 803
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0004f750
[ 0.000000] Readback ErrCtl register=0004f750
[ 0.000000] Memory: 59240K/65536K available (3622K kernel code, 154K rwdata, 452K rodata, 1196K init, 199K bss, 6296K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000019] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.007955] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.050641] pid_max: default: 32768 minimum: 301
[ 0.055619] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.062167] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.079107] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.088808] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.095062] pinctrl core: initialized pinctrl subsystem
[ 0.101448] NET: Registered protocol family 16
[ 0.113768] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.120272] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.181064] Can't analyze schedule() prologue at 80008f38
[ 0.205327] PCI host bridge /fpi at 10000000/pci at E105400 ranges:
[ 0.211024] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.216293] IO 0x000000001ae00000..0x000000001affffff
[ 0.251812] usbcore: registered new interface driver usbfs
[ 0.257437] usbcore: registered new interface driver hub
[ 0.262856] usbcore: registered new device driver usb
[ 0.268389] PCI host bridge to bus 0000:00
[ 0.272445] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.279372] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.286315] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.293168] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.304356] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.311106] pci 0000:00:0f.2: BAR 0: assigned [mem 0x18010000-0x180100ff]
[ 0.317953] pci 0000:00:0f.0: BAR 4: assigned [io 0x1ae00000-0x1ae0001f]
[ 0.324809] pci 0000:00:0f.1: BAR 4: assigned [io 0x1ae00020-0x1ae0003f]
[ 0.333066] clocksource: Switched to clocksource MIPS
[ 0.340642] NET: Registered protocol family 2
[ 0.346533] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.353503] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.359889] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.366476] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.372302] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.378983] NET: Registered protocol family 1
[ 0.383418] PCI: Enabling device 0000:00:0f.0 (0000 -> 0001)
[ 0.389131] PCI: Enabling device 0000:00:0f.1 (0000 -> 0001)
[ 0.394784] PCI: Enabling device 0000:00:0f.2 (0000 -> 0002)
[ 0.415646] gptu: totally 6 16-bit timers/counters
[ 0.420632] gptu: misc_register on minor 63
[ 0.424769] gptu: succeeded to request irq 126
[ 0.429272] gptu: succeeded to request irq 127
[ 0.433783] gptu: succeeded to request irq 128
[ 0.438297] gptu: succeeded to request irq 129
[ 0.442810] gptu: succeeded to request irq 130
[ 0.447323] gptu: succeeded to request irq 131
[ 0.458582] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[ 0.463938] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
[ 0.471588] Crashlog allocated RAM at address 0x3f00000
[ 0.516749] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.522519] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.539691] io scheduler noop registered
[ 0.543558] io scheduler deadline registered (default)
[ 0.549908] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.558879] console [ttyLTQ0] enabled
[ 0.558879] console [ttyLTQ0] enabled
[ 0.565988] bootconsole [early0] disabled
[ 0.565988] bootconsole [early0] disabled
[ 0.575243] lantiq nor flash device: 00800000 at 10000000
[ 0.579482] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.588482] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.593474] Amd/Fujitsu Extended Query version 1.1.
[ 0.598340] number of CFI chips: 1
[ 0.601683] 4 ofpart partitions found on MTD device ltq_nor
[ 0.607040] Creating 4 MTD partitions on "ltq_nor":
[ 0.611778] 0x000000000000-0x000000030000 : "uboot"
[ 0.623138] 0x000000030000-0x000000040000 : "uboot_env"
[ 0.630822] 0x000000040000-0x0000007f0000 : "firmware"
[ 0.667713] 2 uimage-fw partitions found on MTD device firmware
[ 0.672165] 0x000000040000-0x00000019f30b : "kernel"
[ 0.680094] 0x00000019f30b-0x0000007f0000 : "rootfs"
[ 0.687545] mtd: device 4 (rootfs) set to be root filesystem
[ 0.691831] 1 squashfs-split partitions found on MTD device rootfs
[ 0.697747] 0x000000540000-0x0000007f0000 : "rootfs_data"
[ 0.706889] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.729148] switch0: Atheros AR8216 rev. 1 switch registered on 1e180000.etop-ffffffff
[ 0.768153] libphy: ltq_mii: probed
[ 0.806423] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ffffffff:00, irq=-1)
[ 0.816481] wdt 1f8803f0.watchdog: Init done
[ 0.827199] NET: Registered protocol family 10
[ 0.845856] NET: Registered protocol family 17
[ 0.848912] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.861138] 8021q: 802.1Q VLAN Support v1.8
[ 0.873932] fdt: not creating '/sys/firmware/fdt': CRC check failed
[ 0.891435] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.904610] Freeing unused kernel memory: 1196K
[ 3.207397] init: Console is alive
[ 3.209894] init: - watchdog -
[ 4.566310] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.675908] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.692323] init: - preinit -
[ 5.668439] random: procd: uninitialized urandom read (4 bytes read, 22 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.099604] jffs2: notice: (399) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.117585] mount_root: switching to jffs2 overlay
[ 9.142946] urandom-seed: Seeding with /etc/urandom.seed
[ 9.520910] procd: - early -
[ 9.522658] procd: - watchdog -
[ 10.278927] procd: - watchdog -
[ 10.281620] procd: - ubus -
[ 10.495463] random: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available)
[ 10.509711] random: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available)
[ 10.517987] random: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available)
[ 10.525955] random: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available)
[ 10.544845] random: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available)
[ 10.553152] random: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available)
[ 10.561690] random: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available)
[ 10.570293] random: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available)
[ 10.579447] procd: - init -
Please press Enter to activate this console.
[ 11.448692] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.464195] ipip: IPv4 over IPv4 tunneling driver
[ 11.487379] l2tp_core: L2TP core driver, V2.0
[ 11.498827] l2tp_netlink: L2TP netlink interface
[ 11.511353] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 11.523395] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 11.539131] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 11.587035] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.639010] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 11.645502] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 11.762334] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded
[ 11.812856] u32 classifier
[ 11.814188] input device check on
[ 11.817703] Actions configured
[ 11.831903] Mirror/redirect action on
[ 11.854407] nf_conntrack version 0.5.0 (944 buckets, 3776 max)
[ 11.907973] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.071540] xt_time: kernel timezone is -0000
[ 12.116829] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.042655] random: jshn: uninitialized urandom read (4 bytes read, 60 bits of entropy available)
[ 31.343911] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 31.402127] device eth0.1 entered promiscuous mode
[ 31.405512] device eth0 entered promiscuous mode
[ 31.437024] IPv6: ADDRCONF(NETDEV_UP): br-dhcp: link is not ready
[ 32.593202] random: nonblocking pool is initialized
[ 33.177487] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 33.192731] br-dhcp: port 1(eth0.1) entered forwarding state
[ 33.197032] br-dhcp: port 1(eth0.1) entered forwarding state
[ 33.228915] IPv6: ADDRCONF(NETDEV_CHANGE): br-dhcp: link becomes ready
[ 35.197145] br-dhcp: port 1(eth0.1) entered forwarding state
> Am 11.02.2019 um 15:57 schrieb Stefan W. <wuchi at protonmail.com>:
>
> Hallo Matthias!
>
> Unter http://lernekultur/ffbf/ findest Du im Stable branch 1.0.2 Images für Deine EasyBox 803A (ARV752DPW22).
>
> Ich habe kein solches Gerät hier, könnte aber evtl. eines besorgen für den Fall, dass Du Teile des Flashs tatsächlich überschrieben hast.
>
> Viel Spass beim Ausprobieren und viele Grüße!
>
> - Stefan
>
>
>
> ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐
> On Saturday, 9. February 2019 09:53, Matthias Klose <matthias at klose.berlin> wrote:
>
>> Hi!
>>
>> Hat jemand Erfahrung mit der Kiste, oder freundlicher Weise die Möglichkeit, vielleicht zu sogar Mittwoch, ein tunneldigger-Image (1.0.2) für die 803A [0][1] zu bauen?
>> U-Boot hab ich schon drauf per Serial, OpenWrt 18.06.2 bootet auch, aber die Wifi-Treiber initialisieren noch nicht richtig, er hängt bei
>>
>> [ 12.796221] rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"
>>
>> Gruß Matthias
>>
>> [0] https://openwrt.org/toh/hwdata/arcadyanastoria/arcadyanastoria_arv752dpw22_easybox803a
>> [1] https://openwrt.org/toh/astoria/arv752dpw22
>>
>> gesourctes:
>> https://wiki.freifunk-cottbus.de/anleitungen:firmware_selbst_bauen
>> https://lab.ks.uni-freiburg.de/projects/linux_from_scratch/wiki/EasyBox_flashen#EasyBox-flashen
>> https://clockworkbird9.wordpress.com/2014/12/25/when-easybox-803-a-meets-openwrt/
>>
>>
>
> _______________________________________________
> Berlin mailing list
> Berlin at berlin.freifunk.net
> http://lists.berlin.freifunk.net/cgi-bin/mailman/listinfo/berlin
> Diese Mailingliste besitzt ein �ffentlich einsehbares Archiv
Mehr Informationen über die Mailingliste Berlin